Main Categories

The present document specifies technical characteristics and methods of measurements for ground based monostatic ATC solid state primary surveillance radars that are intended to work with a waveguide-based rotating passive antenna and have the following characteristics:

• operation in the 1 215 MHz to 1 400 MHz frequency range;

• transmitter output peak power up to 100 kW;

• the transceiver output uses an RF circulator;

• a piece of waveguide of at least 66 cm is integral to the transceiver.

NOTE 1: Phased array ATC primary surveillance radars are not covered by the present document.

NOTE 2: 66 cm equals 2 times the cut-off wavelength of a WR650/WG6/R14 waveguide which is typically used in

the 1 215 MHz to 1 400 MHz frequency range.

NOTE 3: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.1] is given in Annex A. 

The present document specifies technical requirements, limits and test methods for Level Probing Radar (LPR) 
equipment operating in the frequency ranges 6 GHz to 8,5 GHz, 24,05 GHz to 26,5 GHz, 57 GHz to 64 GHz, 75 GHz to 
85 GHz for strictly vertical downward installation in outdoor as well as indoor environments. 
Level Probing Radars in the scope of the present document consist of a combined transmitter and receiver and are 
equipped with an integral or dedicated antenna provided also by the EUT manufacturer. EUTs intended to be equipped 
with antennas from third-party manufacturers are not covered by the scope of the present document. 
LPR equipment and the related categorization is further specified in clause 4.2. 
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive 
2014/53/EU [i.1] is given in Annex A.

The present document provides an overview of the Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.3] based 
certificate profiles and the statements for EU Qualified Certificates specified in other parts of ETSI EN 319 412 ([i.4] to 
[i.7]). It specifies common data structures that are referenced from other parts of ETSI EN 319 412 ([i.4] to [i.7]). 
The profiles specified in this multi-part deliverable aim to support both Regulation (EU) No 910/2014 [i.9] and the use 
of certificates in a wider international context. Within the European context, it aims to support both EU Qualified 
Certificates and other forms of certificate.

The present document specifies requirements on the content of certificates issued to natural persons. This profile builds 
on IETF RFC 5280 [1] for generic profiling of Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.3]. 
This profile supports the requirements of EU Qualified Certificates as specified in the Regulation (EU) 
No 910/2014 [i.5] as well as other forms of certificate. The scope of the present document is primary limited to 
facilitate interoperable processing and display of certificate information. This profile therefore excludes support for 
some certificate information content options, which can be perfectly valid in a local context but which are not regarded 
as relevant or suitable for use in widely deployed applications. 
The present document focuses on requirements on certificate content. Requirements on decoding and processing rules 
are limited to aspects required to process certificate content defined in the present document. Further processing 
requirements are only specified for cases where it adds information that is necessary for the sake of interoperability. 
Certain applications or protocols impose specific requirements on certificate content. The present document is based on 
the assumption that these requirements are adequately defined by the respective application or protocol. It is therefore 
outside the scope of the present document to specify such application or protocol specific certificate content. 

The present document specifies a certificate profile for web site certificates that are accessed by the TLS protocol [i.1]. 
The profile defined in the present document builds on the CA/Browser Forum Baseline requirements [2], Extended 
validation guidelines [3] and other parts of the present multi-part deliverable. 
The present document focuses on requirements on certificate content. Requirements on decoding and processing rules 
are limited to aspects required to process certificate content defined in the present document. Further processing 
requirements are only specified for cases where it adds information that is necessary for the sake of interoperability. 
This profile can be used for legal and natural persons. For certificates issued to legal persons, the profile builds on the 
CA/Browser Forum EV Profile [3] or baseline requirements [2]. For certificates issued to natural persons, the profile 
builds only on CA/Browser Forum baseline requirements [2].

The present document defines specific QCStatement for the qcStatements extension as defined in IETF RFC 3739 [2],
clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these QCStatements can be used
for other forms of certificate.
The QCStatements defined in the present document can be used in combination with any certificate profile, either
defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere.
The QCStatements defined in clause 4.3 can be applied to regulatory environments outside the EU. Other requirements
specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other regulatory
environments.

The present document specifies technical requirements, limits and test methods for Tank Level Probing Radar (TLPR) 
equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57 GHz 
to 64 GHz and 75 GHz to 85 GHz. 
Tank Level Probing Radars in the scope of the present document consist of a combined transmitter and receiver and are 
equipped with an integral or dedicated antenna provided and specified by the EUT manufacturer. 
Further details of the covered TLPR EUT can be found in clause 4.2 of the present document. 
Technical and regulatory requirements for TLPR are provided in European Commission Implementing Decision (EU) 
2025/105 [i.5]. 
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive 
2014/53/EU [i.1] is given in Annex A. 

The present document specifies the technical requirements, limits and test methods for material sensing devices using
UWB technology exterior material sensing devices for ground based vehicles below 10,6 GHz.
The present document only covers non-contact based UWB material sensing devices with antenna connectors according
to ECC/DEC(07)01 [i.1] and Commission Decision 2024/1467/EU [i.2].
Further details of the covered EUT for external material sensing applications for ground-based vehicles and the related
categories can be found in clause 4.2 of the present document.
NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.3] is given in annex A.